If You Get Celfer, the Cheaper Alternative to Thermage, You’ll Get the Most Out of It

Hello, I’m Dr. Jo Won-jin, and I’ve been seeing patients for 10 years.

If Celfer is the cheaper alternative to Thermage, doesn’t the effect drop a bit too?

That’s a perfectly reasonable concern.

The privilege of a later-generation device is that it can review and improve.

Because it compensates for the shortcomings of existing devices while delivering good results, it can be cost-effective.

Today,

under the topic of “If You Get Celfer, the Cheaper Alternative to Thermage, You’ll Get the Most Out of It,”

I’ll talk about the three cases with the highest effectiveness and satisfaction.

Table of Contents

• 1. People who don’t have much facial fat but want both firmness and contouring
• 2. People who want to reduce cheek jowls and a double chin
• 3. People who say, “I absolutely hate pain”

• Summary of the 3 types who can get the most out of Celfer

Celfer, the cheaper alternative to Thermage

1. People who don’t have much facial fat but want both firmness and contouring

(Put simply, this is for people who want both Ulthera and Thermage.)

“I have thin skin and want Thermage because of fine wrinkles. My jawline is also stressful, but I’m scared that if Ulthera is done wrong, I’ll end up with hollow cheeks.”

Celfer is suitable for people with these kinds of combined concerns.

Usually, to address these concerns, you would need both Ulthera and Thermage.

But the cost is not small, and the pain is doubled, so some people find it burdensome.

In cases like this, Celfer can be a good alternative.

That’s because Celfer can freely combine two wavelengths.

• Superficial layer: smooths the skin surface as if ironing it, improving pores and fine wrinkles (the role of Thermage)

• Deeper layer: energy penetrates deep into the skin to refine the contour (the role of Ulthera)

In particular, for people who don’t have much facial fat, if the energy goes in too deeply,

the cheeks can actually look sunken.

Since Celfer can adjust energy in three levels,

the depth can be customized while considering skin thickness.

Shallow for areas with little cheek fat, deeper for the jawline.

Nothing is 100%, of course,

but if energy and depth are delicately adjusted by area,

there’s no need to worry too much about hollow cheeks.

Celfer, the cheaper alternative to Thermage 2. People who want to reduce cheek jowls and a double chin

As we age, cheek jowls descend like a bulldog’s.

A double chin also becomes more prominent.

At this point, simply tightening the skin is not enough.

You need to reduce the heavy, sagging fat.

For cheek jowls, nasolabial folds, and double chins,

there is some overlap with the know-how used in Ulthera treatments,

so it would be good to read the article below before getting treated.

Back to the topic,

Celfer’s deeper wavelengths are excellent for tightening sagging fat layers.

It reduces unnecessary volume and helps lift the jawline.

So after the procedure, not only skin texture and pores, but also the contour become more refined.

I mentioned people with thin skin earlier,

but in fact, people with thicker skin can also feel noticeable improvement with Celfer.

One reason is that the total amount of energy delivered is greater.

That’s because of the tip size.

As shown in the photo below, the rectangular tip is 1.5 times larger than the Thermage tip.

This means that even if you receive 600 shots with Celfer, you can practically feel the energy efficiency of more than 800 shots.

On top of that, it can deliver energy to deeper layers than Thermage...

So it’s a device that responds well for people with thicker skin who need contour refinement.

Celfer, the cheaper alternative to Thermage 3. People who say, “I absolutely hate pain”

“I can’t do lifting devices because I heard they hurt. I’m even scared of sedation anesthesia.”

This is also a good option for people like that.

The reason lifting hurts is that the energy goes in strongly all at once, stimulating the nerves.

But Celfer breaks the energy into very small pieces and delivers it as gently as possible.

Even with the same amount of energy, being hit all at once and being gently pushed in over ten separate times feels completely different.

Its cooling system is also well-designed, so there’s no burning-like sensation on the skin.

In fact, one of our staff members received Celfer without even using numbing ointment.

She said it felt warm and cool at the same time.

She was very happy that it didn’t hurt.

When patients are comfortable, I can also take more care in delivering the energy.

Even so, if you still have lingering attachment to Thermage,

please be sure to read the article below before getting treated.

Summary of the 3 types who can get the most out of Celfer

• Combined concerns: People with little facial fat who want to improve fine wrinkles and contour lifting at the same time

• Contour refinement: People who want to reduce unnecessary fat in the cheek jowls and double chin to make the face look smaller

• Pain sensitive: People who want a comfortable procedure without worrying about pain and without sedation anesthesia

If even one of these three applies to you, Celfer will be a cost-effective treatment with high satisfaction relative to the price.

Of course, no matter how good a device is, it’s useless if it doesn’t suit your face.

Rather than blindly chasing trendy procedures, the best treatment is the one that fits your own facial condition.

How to find a dermatology clinic that honestly recommends the procedure that suits you,

I wrote about it in the article below.

Thank you. This was Jo Won-jin.